The DSZ 100 features C/Ku-Band compatible, color on-screen displays, up to 45 satellites can be programmed, 150 favorite channel memory, S-Video output, parental control by, satellite, channel or category, dual LNB compatible and a UHF remote.  The DSZ 200 has the same features plus a built in TI filter and programmable multi-mode event timer.

LEGEND

Blue = Buttons on Remote or Receiver

HOW TO rePROGRAM A SATELLITE

1. Go to the satellite you want to reprogram.  If you are not getting a picture, use RIGHT/LEFT ARROWS until you find a picture and identify what satellite you are actually on.  If it is not the one you are looking for, use RIGHT/LEFT ARROWS until you find the correct satellite.  If you are getting a picture, identify what satellite you are actually receiving, then use RIGHT/LEFT ARROWS until you find the correct satellite..   **If you cannot find the correct satellite using this method, then see Programming a New Satellite. **

2. Press MENU.  You will see “Mode Menu”.  The pointer should be at “User Mode”. If it is not, use UP/DOWN ARROWS until the pointer is at “User Mode”.  Then press ENTER.

3. You will then see the “User Mode” menu on the screen.  Tap DOWN ARROW until the pointer is at line number 5 for Video/Dish Fine Tune.  Then press ENTER.

4. The “Video/Dish Fine Tune” menu will now appear on the screen.  The pointer will be at “Video Fine Tune”.  Tap DOWN ARROW until the pointer is at “Dish Fine Tune”.  Then press ENTER.  “INPUT PASSWORD” will appear on the screen. Using the number buttons on the remote press 6-7-8-9.  DO NOT PRESS ENTER.   Make sure the picture is at the clearest point by using RIGHT/LEFT ARROWS, then press ENTER.  The polarity will now tune automatically.  When it is finished “DISH POSITION UPDATED” will appear on the screen.

**If you lose the picture after the polarity tunes automatically you will need to tune the Polarity Manually.

HOW TO ADJUST POLARITY MANUALLY

1. Press MENU.  You will see “Mode Menu”. The pointer should be at “User Mode”. 

2. Tap DOWN ARROW until the pointer is at “Program Mode”.  Then press ENTER. “INPUT PASSWORD” will appear on the screen.

3. Using the keypad on the remote, press A-B-C-E.  You should see the “Program Mode” menu on the screen.

4. Use DOWN ARROW until the pointer is at line number 3 for “Channel Update”. Then press ENTER.  You will see the “Channel Update” menu on the screen.

5. Move the pointer down to “Polarity Move” by tapping DOWN ARROW.  Then use RIGHT/LEFT ARROWS until the best picture is obtained. Then press ENTER to store polarity settings.

HOW TO PROGRAM A NEW SATELLITE:

1. Go to a satellite next to or near the one you want to program.  It is much easier if you start on a satellite that is the same polarity format.

2. a.  If you start on a satellite with the same polarity format, tap the RIGHT/LEFT ARROWS on the remote until you find the correct satellite.  Then go to Step 3.

b.  If you start on a satellite with the opposite polarity format, tap RIGHT/LEFT ARROWS until you lose the picture.  Then press MENU.  You will see “Mode Menu”. The pointer should be at “User Mode”.  Tap DOWN ARROW until the pointer is at “Program Mode”.  Then press ENTER. “INPUT PASSWORD” will appear on the screen.   Using the keypad on the remote, press A-B-C-E.  You should see the “Program Mode” menu on the screen.  Use DOWN ARROW until the pointer is at line number 3 for “Channel Update”. Then press ENTER.  You will see the “Channel Update” menu on the screen.  Move the pointer down to “Polarity Move” by tapping DOWN ARROW.  Then use RIGHT/LEFT ARROWS until the best picture is obtained. Then press ENTER to store polarity settings.

3. Press MENU.  You will see “Mode Menu”. The pointer should be at “User Mode”.  Tap DOWN ARROW until the pointer is at “Program Mode”.  Then press ENTER. “INPUT PASSWORD” will appear on the screen.  Press A-B-C-E.  You should see the “Program Mode” menu on the screen.  Use DOWN ARROW until the pointer is at line number 2 for “Satellite Update”, then press ENTER.  See Figure 1 below.

Figure 1
_____________________________

2. Satellite Update 

Add New Satellite
            Format: 
            Sat Type:
            Erase Satellite
            Restore Satellite
            Dish Fine Tune
            Input New Sat Type
_____________________________

4. The pointer should be at “Add New Satellite”.  If not use UP/DOWN ARROWS until the pointer is at “Add New Satellite”.  Using the keypad on the remote, press the correct satellite name.  

5. Tap DOWN ARROW until the pointer is at “Format”.  Use RIGHT/LEFT ARROWS until the correct format is shown.  Use “Four GHZ 2” for Galaxy type satellites and use “Four GHZ 1” for Spacenet or Telstar type satellites.

6. Tap DOWN ARROW until the pointer is at “Sat Type”.  Then use RIGHT/LEFT ARROWS until the correct type is shown.  Use “Galaxy” for Galaxy type satellites (ex: G1, G5, M2, GE1) and use “Spacenet”, “Telstar”, and “Satcom” for Spacenet, Telestar, and Satcom type satellites (ex: C1/F1, G9, S4, GE2, GE3).

7. Now press UP ARROW until the pointer is back to “Add New Satellite” and then press ENTER.   You should see a line that says “Go to this line and press enter”.  Use UP/DOWN ARROWS until the pointer is at that line and then press ENTER.

8. You should now see:

                                    2. Satellite Update

                                    (Add New Satellite) 

                                    Satellite:  (The new name will appear here)

 9. Press ENTER to store changes.  The polarity will tune automatically. If you lose the picture after the polarity tunes automatically, then see Polarity Tuning to tune the polarity manually and store it. If the picture is OK then the process is complete.