• On / Off
• Scan - Scans all channels in about 4 seconds. Used as an aid in locating satellites
• Sat - Used with the number buttons to call a satellite
• Mode (AM/PM) - Selects AM or PM when programming time and Selects either mono, discrete or matrix audio.
• Down / Up - Used with the SAT button to scroll through the satellites.
• Preset - Selects 1 of 6 preset audio modes (1,2,3 - factory prog.;
• 4,5,6 - personal prog.)
• Select - Used with button 0-9 when programming information into receiver.
• Tune "A" Up/Down - Changes frequency of Channel A
• H/V - Changes Polarity
• Tune "B" Up/Down - Changes frequency of Channel B when in Stereo mode. "EE" will appear if pressed and it is in mono mode.
• Volume Up/Down
• Clear - Used in the Programming mode to clear any instruction.
• Channel Up/Down

• [Numbers 0-9] - Used to select a channel or a satellite in conjunction with the SAT button
• [Up/Down arrows] - Used to changed channels
• Clock - Displays the time
• Sat - Used to select a satellite. (i.e.: SAT 0 2). When pressed while the dish is moving, it will stop at the closest satellite. If it is pressed while the display reads "P##" or with a satellite number that is not programmed, then "EE" will appear on the display.
• Mute
• On/Off
• F Tune Up/Down - Adjusts the video fine tune
• Volume Up/Down

• Audio Preset Indicator - Shows which one of the six presets the receiver is in.
• Audio Mode Indicator - Shows which audio mode the receiver is in.
• Audio Channel Indicator - Shows whether it is in Channel A or Channel B.

These type of receivers do not go by satellite names, the customer should have a list of numbers that correspond to the satellites. (EX: Satellite 01 will be F1, 02 is F4, etc.).

1. Find a satellite number that the customer does not use.

2. Start on a satellite next to or near the satellite that is being programmed.

3. Go to a channel that is active on both the satellite you are starting from and the satellite

to be programmed.

4. Press selecT; display reads [‘SEL].

5. Press zero (0) twice; display reads [00] then [ID].

6. Press the ID code which is factory preset at 1, 2, 3; display reads [C##]. If 1, 2, 3 does not work then go to "How to Change the ID Code if it is Forgotten".

7. Follow the correct procedure:

[A] If you are starting from a satellite with the opposite polarity, tap the UP (east) or DOWN (west) button just until the picture is gone.

-Next, press the H/V button on the receiver one time to reverse the polarity; display reads [‘H EN] for normal polarity or [‘H OD] for reversed polarity.

-If there is a picture at this time and it is the correct satellite, then proceed to step 8; otherwise continue moving up or down.

[B] If you are starting from a satellite with the same polarity, then tap the UP (east) or DOWN (west) button until a different picture comes in. If the picture is correct, then proceed to step 8; otherwise continue moving.

8. To store the satellite: Press select, display reads [‘SEL]; press 1, 2; display reads [‘PP], then press the number of the satellite you are storing (from 1-33). Press select again; display reads [‘PP##] then [‘C##].

9. To exit the programming mode: Press select, display reads [‘SEL]; then zero (0) twice; display reads [‘C##].

10. This completes the programming process.

1. Press select; display reads [‘SEL].

2. Press 0 twice; display reads [00] then [ID].

3. Press 1, 2, 3; display reads [C##].

4. Press select; display reads [‘SEL].

5. Press 1, 3; display reads [‘PE].

6. Press the number of the satellite to be erased; display reads [‘P##].

7. Press select and the satellite should be erased now; display reads [‘SEL].

8. Press select, then 0 twice to exit the programming mode; display reads [C##].

1. Press select; display reads [‘SEL].

2. Press 0 twice; display reads [00] then [ID].

3. Press 1, 2, 3; display reads [C##].

4. Press select; display reads [‘SEL].

5. Press 1, 8; display reads [‘ID].

6. Press any three digit number you want to be the code; display reads [‘C##].

7. Press select, then 0 twice to exit the programming mode; display reads [C##].

1. Press select; display reads [‘SEL].

2. Press 6 1; display reads [61 momentarily].

3. Press 8 5 2; display reads [C##].

4. The ID code is now set to 1, 2, 3 as it was originally.

1. Go to the channel that is to be locked or unlocked.

2. Press select; display reads [‘SEL].

3. Press 0 twice; display reads [00] then [ID].

4. Press 1, 2, 3; display reads [C##].

5. Press select; display reads [‘SEL].

6. Press 1, 2, 3, 4, 5, 6; display reads [‘CL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘CL], then [OFF], then [‘C##] if the lock was turned off.

7. Press select; display reads [‘SEL].

8. Press 0 twice; display reads [CL].

1. Go to the satellite that is to be locked on or lock removed.

2. Press select; display reads [‘SEL].

3. Press 0 twice; display reads [00] then [ID].

4. Press 1, 2, 3; display reads [C##].

5. Press select; display reads [‘SEL].

6. Press 1, 4; display reads [‘PL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘PL], then [OFF], then [‘C##] if the lock was turned off.

7. Press select; display reads [‘SEL].

8. Press 0 twice; display reads [‘C##].

1. Go to the satellite and channel that is to be locked on or lock removed.

2. Press select; display reads [‘SEL].

3. Press 0 twice; display reads [00] then [ID].

4. Press 1, 2, 3; display reads [C##].

5. Press select; display reads [‘SEL].

6. Press 1, 5; display reads [‘SL], then [‘ON], then [‘C##] if the lock was turned on. The display will read [‘SL], then [OFF], then [‘C##] if the lock was turned off.

7. Press select; display reads [‘SEL].

8. Press 0 twice; display reads [‘C##].